A Beginner's Guide to Installing a Bathtub
A Beginner's Guide to Installing a Bathtub
Blog Article
Just how do you actually feel about How to Install a Bathtub Yourself?
Mounting a bathtub isn't precisely brain surgery, yet it does call for solid plumbing, carpentry, and often, tiling abilities. Replacing an old bathtub with a new one is also a moderately challenging job. If the old tub is easily easily accessible, the project can relocate speedily; if you have to open a wall surface to get rid of the old bathtub and place the new bathtub, the job is a lot harder. In either situation, the job is within a home handyman's skills, although you will certainly require a helper to move out the old bathtub and also embeded in the new one. Ensure you have certified yourself for the work and fit attempting it. Instead of hiring a professional to take control of a halfway-completed job, it is better to take into consideration employing one prior to you begin. Opportunities are you may need an expert plumber to make tube connections.
This short article will certainly assist you mount a new tub in your bathroom if you have already gotten a brand-new tub as well as do not need to change the setup of your previous supply of water pipelines.
Your tools as well as material checklist must make up the following:
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your setup, then the first thing you need to do is disconnect the water. After doing so, activate the taps to drain any water staying in the system. The procedure of getting rid of the existing faucets can be fairly bothersome because of the restricted access that is typically the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a cloth all set for the staying water that will originate from the pipes. As soon as the supply pipes have actually been eliminated, make use of the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this procedure. When the faucets have actually been removed, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
Before moving on to fit the new faucets, contrast the pipe connections on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will need a plastic adapter to stop damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the various other end offers a connection to the current supply pipes.
If you need to fit a monobloc, after that you will call for minimizing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, place the tap in the placing hole in the bath/basin ensuring that the washers remain in area between the faucet and the sink. Protect the faucet in place with the maker given backnut. Once the faucet is securely in place, the supply pipelines can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with typical faucet adapters. The former kind should be linked to the faucet finishes first, tightening just by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Bathtub
Utilizing the two wood boards under its feet, place the tub in the called for setting. The wooden boards are helpful in uniformly spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 small points.
The next objective is to ensure that the tub is leveled all round. This can be accomplished by examining the level and also readjusting the feet on the bathtub until the spirit level reads level.
To set up taps, fit the bottom of the furthest versatile faucet adapter to the appropriate supply pipe by making a compression sign up with; after that do the very same for the various other tap.
Switch on the supply of water and examine all joints as well as brand-new pipework for leaks and also tighten them if essential. Load the bathtub and also examine the overflow electrical outlet as well as the typical electrical outlet for leakages.
Finally, take care of the bathroom paneling as described in the manufacturer's instruction manual. Tiling as well as sealing around the bathtub ought to wait up until the bathtub has actually been made use of a minimum of once as this will certainly settle it into its final placement.
Preparing for the Installation
Firstly, the supporting structure provided with the bathroom ought to be fitted (if called for) according to the supplier's directions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is very important to ensure that if the tap features a plastic washer, it is fitted between the bath and the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the taps device to avoid pressure on the bath tub.
Fit the flexible faucet connectors to the bottom of the two faucets using 2 nuts and also olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you use every one of the provided washers.
Attach the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bath must now be ready to be fitted in its final setting.
Tiling Around the Bath tub
In the area where the bath satisfies the floor tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate sufficient to fracture a rigid seal, triggering the water to penetrate the wall between the bath as well as the tiling, leading to difficulties with wetness as well as feasible leakages to the ceiling below.
You can select from a variety of coloured sealants to blend in your fixtures and also installations. They are marketed in tubes as well as cartridges, and also are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with twists of soaked paper or soft rope. Remember to always fill the bathtub with water before securing, to allow for the motion experienced when the bathtub is in usage. The sealer can crack rather very early if you do not think about this movement prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise conveniently offered on the marketplace. It is advisable to fit the ceramic tiles making use of waterproof or water resistant glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you appreciate reading about A Step-by-Step Guide to Installing a Bathtub? Give a comment down the page. We'd be interested to hear your feelings about this blog posting. We hope that you visit us again in the future. Loved our blog? Please share it. Let somebody else check it out. Kudos for your time. Don't hesitate to come by our site back soon.
Plumbing challenges? Get immediate solutions. Report this page